资料详情

基于AT89S52单片机的汽车防盗报警系统设计 毕业论文

头像

51单片机

编号:4443

摘要

随着科学技术的进步,为对付不断升级的盗车的段,人们研制开发了不同方式构造的防盗器。

本设计以单片机AT89S52作为控制核心,从单片机最小系统设计、防人接近热释电检测电路的设计、玻璃防震、车身防击的振动检测电路的设计、防车门开启检测电路的设计、防接近驾驶座电路、汽车点火闭锁电路的设计、无线遥控电路及无线报警电路的设计等几个方面出发,详细研究和设计了汽车防盗报警器的各个局部容,设计了单片机及其外围电路,并结合一套经典的程序算法。给出了一套合理的汽车防盗报警器软硬件解决方案。

关键词单片机  热释电  多普勒效应  振动  无线报警  遥控

Abstract

With the scientific and technological progress, to bat the escalating car theft in the section, people developed different ways to structure the anti-theft device.

ThedesignMCU AT89S52 as thcontrol, fromthe microputer system design, anti-people close to the pyroelectric detection circuit design, glass vibration, the vibration of the body against attack detection circuit design, anti-detection circuit to open the door, anti-nearly driving Block circuit, car ignition locking circuit design, wireless remote control circuit and the design of wireless alarm circuit aspects of starting a detailed study and design of the vehicle anti-theft alarm in all parts of the design of the microcontroller and its peripheral circuits, bined with a set of the classic program algorithm. Given a reasonable car burglar alarm hardware and software solutions.

Keywords:SCMPyroelectricDopplereffectVibrationWireless AlarmRemotecontrol


目录

摘要

Abstract

Keywords:SCMPyroelectricDopplereffectVibrationWireless AlarmRemotecontrol

第一章    绪论

1.1 汽车防盗报警器的开展趋势

1.2汽车防盗报警器的设计要求

第二章    系统的总体设计

2.1 各检测模块电路方案确实定

2.1.1 人接近汽车检测传感器―热释电传感器

2.1.2 车身冲击振动检测传感器―压电瓷传感器

2.1.3 车门开启检测传感器―干簧管

2.1.4  接近驾驶座检测传感器―多普勒效应传感器

2.2 电路总体设计方案确实定

第三章 系统的硬件电路设计

3.1 报警检测电路的设计

3.1.1 热释电红外传感器检测电路的设计

3.1.2干簧管车门开启检测电路的设计

3.1.3压电瓷振动检测电路的设计

    LM393作为专用比拟器集成电路,其输出为集电极开路输出,两个比拟器的输出可直接并联,共用外接电阻,它可以双电源供电,也可以单电源供电。该比拟器的电源电压是2~36V或,输出电流大,可直接驱动TTL和LED。类似型号是LM219,四电压比拟器LM319。LM139、LM239和LM339与LM119的功能根本一样。LM393的符号见图3-6。其中11脚为正电源,6脚为电源地,3脚为比拟器1的地线,8脚为比拟器2的地线。

3.1.4 多普勒接近座位检测电路的设计

3.2 无线发射和接收电路的设计

3.2.1 编码芯片HS2262

3.2.2 解码芯片HS2272

3.2.3 射频发射-接收模块

3.2.4 无线发射-接收电路图的设计

3.3 单片机最小系统设计

1、AT89S52概述

2、AT89S52引脚功能介绍

3〕控制信号引脚RST

3.4 点火闭锁电路设计

3.5 声光报警电路的设计

第四章 系统的软件设计

4.1 Keil C51简介

4.2 系统的中断效劳程序

INT0中断效劳程序

4.3 系统的主程序流程

#define uint unsigned int

结论与展望

致  谢

参考文献

附录一:多功能汽车防盗报警器电路图

外文翻译及原文

The automatic gearbox